دانلود کتاب 6th International Conference on Adhesive Bonding 2021: Selected Contributions of AB 2021

فهرست مطالب :

Preface
Contents
Open Assembly Time of Water-Borne Polyvinyl Acetate (PVAc) Wood Adhesives Affected by Various Factors
1 Introduction
2 Materials and Methods
2.1 Adhesive System Characteristics
2.2 Experimental Designs
2.3 Influence of Temperature on Viscosity
2.4 Procedure for Determining the Open Time
2.5 Statistical Analyses
3 Results and Discussion
4 Conclusion
References
Engineering Technology and Preparation of Coating Systems Made with Epoxy Resin-Based Bonding Agents Modified with the Addition of Granite Powder Sourced from Quarry Wastes
1 Introduction
2 Materials and Methods
2.1 Concrete Substrate
2.2 Waste Granite Powder
2.3 Epoxy Resin
2.4 Preparation of Coating Systems
2.5 Pull-Off Strength Test of Epoxy Resin-Based Bonding Agents
3 The Pull-Off Strength Results of the Epoxy Resin Bonding Agent
4 Cost-Economic Analysis
4.1 Mechanical and Cost Analysis of the Tested Coating
5 Conclusions
References
Mechanical and Adhesive Properties of Cement-Lime Plasters Modified with Waste Granite Powder
1 Introduction
2 Materials and Methods
2.1 Blend Design of Composites and Sample Preparation
2.2 Determination of Consistency of Fresh Mortars
2.3 Determination of Volumetric Density of Wet Mortar
2.4 Determination of Basic Mechanical Properties of Hardened Mortars
2.5 Determination of Adhesion of Hardened Mortars to the Substrate
2.6 Water Absorption Test
3 Results
3.1 Determining the Properties of Fresh Mortars
3.2 Determination of Basic Mechanical Properties of Hardened Mortars Modified with Granite Powder
3.3 Determination of Adhesion of Hardened Mortars to the Substrate
3.4 Water Absorption Test
3.5 Comparison of Obrained Results and Literature Review
4 Conclusions
References
Characterization of Fast Adhesive Curing Reactions—A Novel Experimental Setup
1 Introduction
1.1 Rheology
1.2 Basics of Induction Heating
1.3 Adhesive Curing Reactions
2 Development of a Novel Experimental Setup
2.1 Profile Phase
2.2 Concept Phase
2.3 Prototype
3 Conclusions
References
Material Extrusion on Enameled Steel Surfaces
1 Introduction
1.1 Motivation
1.2 Objective
2 Experimental Setup
2.1 Substrate
2.2 Pretreatment and Coating
2.3 Material Extrusion
2.4 Mechanical Characterization
3 Results and Discussion
4 Conclusion
References
The Effect of the Viscosity and the Contact Angle on the Pull-Off Strength of Epoxy Resin Modified with Waste Granite Powders
1 Introduction
2 Research Significance
3 Materials and Methods
3.1 Waste Granite Powders
3.2 Epoxy Resin and Mixing Proportions of Epoxy Resin with Waste Granite Powders
3.3 Viscosity Measurements
3.4 Contact Angle Measurements
3.5 Pull-Off Strength Test
4 Results and Discussion
4.1 Viscosity Measurements Results
4.2 Contact Angle Measurements Results
4.3 Pull-Off Strength Test Results
4.4 Dependence of Viscosity and Contact Angle on Pull-Off Strength
5 Conclusions
References
Investigation of the Cleaning Effectiveness of Laser Radiation for Improved Adhesion on Glass Dust Contaminated Glass Fiber Reinforced Polyamide 6
1 Introduction
2 Materials and Methodology
3 Results
4 Conclusion
References
Structural Bonding of Thin-Walled Magnesium Die Cast Components
1 Introduction
2 Experimental Details
3 Results and Discussion
3.1 Influence of the Pretreatment
3.2 Influence of the Release Agent
3.3 Influence of the Type of Flow
3.4 Environmental Testing
4 Conclusions
References
The Behaviour of CFRP Adhesive Joints Under Different Loading Rates
1 Introduction
2 Experimental Details
2.1 Adhesive
2.2 Adherends
2.3 Joint Geometry
2.4 Test Conditions
3 Numerical Details
3.1 Static Analysis
3.2 Impact Analysis
4 Results and Discussion
4.1 Experimental Results—Static Tests
4.2 Experimental Results—Impact Tests
4.3 Numerical Joint Strength Prediction
5 Conclusions
References
Long-Term Resistant Bonding Between Wood and Aluminium Alloy for Hybrid Lightweight Composites
1 Introduction
2 Material and Methods
2.1 Material
2.2 Methods
3 Results and Discussion
3.1 Shear Strength of Single Lap Joints
3.2 4-Point Bending Strength
4 Conclusion
References
Multiaxial Fatigue Life Assessment of Adhesive Joints Based on the Concepts of Critical Planes: Stress-Based Approaches
1 Introduction
2 Stress-Based Multiaxial Fatigue Models
2.1 Critical Plane Concepts
2.2 Stress-Based Critical Plane Fatigue Models
3 Description of the Experimental Program
3.1 Materials and Samples
3.2 Test Device and Loading Conditions
4 Fatigue Life Prediction Procedure
4.1 Finite Element Simulation
4.2 Critical Plane Fatigue Models Constants
5 Results and Discussion
5.1 Finite Element Simulation Results
5.2 Fatigue Models Evaluation
6 Conclusions
References