دانلود کتاب Fatigue and Fracture Mechanics, Volume 37:

فهرست مطالب :

Content:
Front Matter
• Overview
• Table of Contents
•Part I. The Jerold L. Swedlow Memorial Lecture 1. On the Beauty of Analytical Models for Fatigue Crack Propagation and Fracture - A Personal Historical Review
•Part II. Elastic-Plastic Fracture Mechanics and Fracture Mechanisms 2. Investigation of Transition Fracture Toughness Variation within the Thickness of Reactor Pressure Vessel Forgings
3. More Accurate Approximation of J-Integral Equation for Evaluating Fracture Resistance Curves
4. Application of Advanced Master Curve Approaches to the EURO Fracture Toughness Data Set
5. Revisit of ASTM Round-Robin Test Data for Determining R Curves of Thin-Sheet Materials
6. The Analysis of Fracture Mechanisms of Ferritic Steel 13HMF at Low Temperatures
7. A Weibull Stress Model to Predict Effects of Weld Strength Mismatch on Cleavage Fracture Toughness
•Part III. Fatigue Behavior and Life Estimation 8. Fatigue Initiation Modeling of 316LN Steel Based on Nonlocal Plasticity Theory
9. Mechanical Conditioning of Superelastic Nitinol Wire for Improved Fatigue Resistance
10. Creep-Fatigue Relationships in Electroactive Polymer Systems and Predicted Effects in an Actuator Design
11. Effects of Microstructure on the Incipient Fatigue and Fretting Crack Processes in Al-Cu-Li Alloys
12. Development of a Sliding-Rolling Contact Fatigue Tester
•Part IV. Fatigue Crack Growth 13. Determination of ΔKth by Compression Pre-Cracking in a Structural Steel
14. Crack-Closure Behavior of 7050 Aluminum Alloy near Threshold Conditions for Wide Range in Load Ratios and Constant Kmax Tests
15. Definition of the Influence of Pore Size on the Fatigue Limit Using Short Crack Propagation Experiments
16. Fatigue Crack Propagation Behavior of an Inertia Friction Welded α/β Titanium Alloy
17. Fatigue Crack Propagation in SAW Seam Welds of API 5L X42 Steel Pipe in the Radial Short Direction
•Part V. Multiaxial Fatigue and Fracture 18. Fatigue from an Induced Defect: Experiments and Application of Different Multiaxial Fatigue Approaches
19. Effect of Cladding on Biaxially Loaded Underclad Part-through Cracks
20. An Assessment of Cumulative Axial and Torsional Fatigue in a Cobalt-Base Superalloy
21. A Non Local Multiaxial Fatigue Approach to Account for Stress Gradient Effect Applied to Crack Initiation in Fretting
22. Experimental and Numerical Analyses of Fatigue Behavior of Welded Cruciform Joints
•Part VI. Residual Stress Effects on Fatigue and Fracture 23. Importance of Residual Stresses and Surface Roughness Regarding Fatigue of Titanium Forgings
24. Fatigue Assessment of Brazed T-Joints Based on Damage Tolerance Including Residual Stress Effects
25. Residual Strain Effects on Bridging Stress of Cracked and Delaminated Fiber Metal Laminates
26. Elastic-Plastic Stress Analysis of Cold-Worked Pin-Loaded Holes
27.The Influence of Elastic Follow-up on the Integrity of Structures
•Part VII. Fatigue and Fracture under Thermomechanical Conditions 28. Lifetime Calculation of Thermo-Mechanically Loaded Materials (Al, Cu, Ni, and Fe Alloys) Based on Empirical Methods
29. Mesh-Free Solution of Two-Dimensional Edge Crack Problems under Thermo-Mechanical Load
30. Temperature Calibration Techniques for TMF Testing
•Part VIII. Application of Fracture Mechanics and Cohesive Zone Models 31. Fatigue Crack Growth Simulation in Components with Random Defects
32. Cohesive Zone Modeling of Initiation and Propagation of Multiple Cracks in Hard Thin Surface Coatings
33. Modeling of Crack Propagation in Weld Beam-to-Column Connections Submitted to Cyclic Loading with a Cohesive Zone Model
Author Index
Subject Index